OSHA and ANSI Z133 rules for Minnesota tree crews
Which OSHA and ANSI safety rules apply to a tree service crew?
OSHA general industry standards apply to tree care
OSHA states that the tree care industry must comply with all the general industry standards in 29 CFR 1910. There is no single tree standard that replaces them.
Its tree care page lists the ones that come up most: ladders and fall protection, training, vehicle-mounted elevating work platforms, respiratory protection, foot and hand protection, first aid and electrical safety. A bucket truck, a chainsaw and a chipper each pull in different sections.
Build your safety routine from that list, not from what a competitor does.
29 CFR 1910OSHA states that the tree care industry must comply with all the general industry standards in 29 CFR 1910. — Occupational Safety and Health Administration, retrieved 2026-09-29
What ANSI Z133 is, and what it is not
ANSI Z133 is the Safety Requirements for Arboricultural Operations, a voluntary industry standard. OSHA says compliance with ANSI standards does not ensure compliance with OSHA policy.
Saint Paul asks tree license applicants to comply with ANSI Standard A300, which is a separate standard for tree care practice. Keep the two numbers straight on paper: Z133 is safety, A300 is how the work is done.
Following Z133 is good practice and useful evidence in a dispute. It is not a shield from an OSHA citation.
OSHA lists Z133.1, Arboricultural Operations Safety, as a voluntary ANSI standard and notes that compliance with ANSI standards does not ensure compliance with OSHA policy. — Occupational Safety and Health Administration, retrieved 2026-09-29
Saint Paul requires tree trimmer license applicants to comply with ANSI Standard A300. — City of Saint Paul, retrieved 2026-09-29
What an OSHA inspector looks at on a tree job
OSHA's inspection guidance for tree care says falls and struck-by hazards are leading causes of death and serious injury for tree care workers.
Inspectors assess fall protection and anchor points, ladders and aerial devices, protective equipment such as cut-resistant gear and hearing protection, electrical safety near power lines, chainsaw maintenance, first aid and traffic control.
Walk your own job site against that list before a callout. Fixing one item on the truck costs less than explaining it later.
OSHA inspection guidance says fall and struck-by hazards are leading causes of death and serious injury for tree care workers. — Occupational Safety and Health Administration, retrieved 2026-09-29
Inspectors evaluate fall protection and anchor points, aerial devices, protective equipment, electrical safety near power lines, chainsaw maintenance, first aid and traffic safety. — Occupational Safety and Health Administration, retrieved 2026-09-29
Power lines and the line-clearance rule
Electrocution risk arises when a worker, tool or equipment touches an overhead power line. OSHA points to 29 CFR 1910.269, which covers line-clearance tree trimming.
That standard sets safe distances from energized lines and how tools are handled. Working near lines is a specialty, so most crews stop and call the utility.
Make it a written stop rule: if a limb or a rope can reach a line, the job pauses until the line is dealt with.
29 CFR 1910.269OSHA guidance cites 29 CFR 1910.269 for electrocution risk from contact with overhead power lines, including line-clearance tree trimming. — Occupational Safety and Health Administration, retrieved 2026-09-29
Reporting a fatality or serious injury to OSHA
An employer must notify OSHA within 8 hours of a work-related death. It must notify within 24 hours of a work-related in-patient hospitalization, amputation or loss of an eye.
These deadlines run from when you learn of the event, on the crew's clock, not the office's. Put the number and the two deadlines in the truck's incident kit.
The compliance calendar covers dated renewals. This one has no date, so it has to live in the crew's routine.
8 hours / 24 hoursEmployers must notify OSHA within 8 hours of a work-related death and within 24 hours of a work-related in-patient hospitalization, amputation or loss of an eye. — Occupational Safety and Health Administration, retrieved 2026-09-29
Questions
Is ANSI Z133 legally required in Minnesota?
It is a voluntary standard. OSHA says compliance with it does not ensure compliance with OSHA policy, though OSHA inspection guidance refers to Z133 for climbing practices.
Does OSHA have a special standard just for tree care?
OSHA's tree care page says the industry must comply with all general industry standards in 29 CFR 1910, and lists the sections that apply most often.
Who reports an injury if a subcontractor is hurt?
The reporting rule applies to employers and their employees. Whether a worker is an employee is a separate question, so settle it before a job, not after an incident.